Products

KOLATTACK

Icon
KOLATTACK

KOLATTACK is a cement-based adhesive with no vertical slip and extended open time suitable for bonding ceramic tiles, mosaics and stone material (provided it is moisture-stable).

Suitable substrates for the use of KOLATTACK are cement screeds as long as they are sufficiently seasoned and dry, walls with civil plaster or cement mortar and walls in cellular concrete blocks (inside). The laying surfaces must be level, compact, clean, free of dust, crumbly parts and anything else that may compromise good adhesion. Cementitious screeds must have matured for at least 28 days. And the plasters of at least a week per centimeter of thickness. Wet particularly dry and absorbent substrates and even when laying at high temperatures. The supports must be damp but without excess water on the surface.

KOLATTACK IS CLASSIFIED C2TE ACCORDING TO THE EUROPEAN STANDARD EN12004.

AVAILABLE FORMATS - KOLATTACK KT1 WHITE *
CODE WEIGHT PROVIDING
KL1W20 20 KG PALLET 1200 KG
AVAILABLE FORMATS - KOLATTACK KT2 GREY
CODE WEIGHT PROVIDING
KT2G20 20 KG PALLET 1200 KG

* Color available upon request.

ADVICE FOR USE

Surface preparation

Preparation of the substrates: The laying surfaces must be level, compact, clean, free of dust, crumbly parts and anything else that may compromise good adhesion.


Mixing

Pour about 6.0 liters of water into a clean container, add a bag of 20 kg KOLATTACK powder under mixing and mix with a whip drill for about 3 minutes until a creamy and spatulable consistency is obtained.


Application

Apply a thin layer of KOLATTACK using the smooth side of the spatula, then spread the adhesive with the notched trowel with teeth of adequate size to allow total coverage of the back of the tile. Install the tiles on the fresh and sticky product. Tap the tiles carefully with a special rubber hammer to completely cover the back and adjust the dimensions. Lift a tile to check that the back is completely covered.


Consumption

2-5 kg/m2 depending on trowel notched size, type and size of the tile.


Warnings

Product for professional use only. Protect from rain for at least 36 hours and from direct sunlight and frost for at least 5 days. Contains cement which in contact with body sweat produces an irritating alkaline reaction. Use protective gloves and glasses. May cause eye damage. In case of contact with eyes or skin, wash immediately with plenty of water and consult a doctor. Consult the latest version of safety before use. Use at temperatures between + 5 °C and + 35 °C. Keep away from humidity, keep in a dry place.

WARNINGS

Warnings
Danger H318
Causes serious eye damage.
H315
Causes skin irritation.
H335
May cause respiratory irritation.
H317
May cause an allergic skin reaction.
P261
Avoid breathing dust.
P280
Wear protective gloves/ protective clothing / eye protection / face protection.
P302+P352
IF ON SKIN:
wash with plenty of water.
P305+P351+P338
IF IN EYES:
rinse cautiously with water for several minutes.
remove contact lenses, if present and easy to do. Continue rinsing.
P310
Immediately call a POISON CENTER / doctor.
Contains
PORTLAND CEMENT- Cr (VI) < 2ppm, may produce an allergic reaction.

CE - 19

LEIK SPA - Via Alessandro Volta 10
46040 - Ponti sul Mincio - Mantova
KOLATTACK KT2 GRIGIO - CPR-0051905


EN 12004
Improved cementitious adhesive for internal and external tiling on floors and walls

Reaction to fire:
Class F
Bond strength, as:
 
Early tensile adhesion strength:
≥ 1,0N/mm²
Durability for:
 
Tensile adhesion strength after heat ageing:
≥ 1,0N/mm²
Tensile adhesion strength after water immersion:
≥ 1,0N/mm²
Tensile adhesion strength after freeze/thaw cycles:
≥ 1,0N/mm²
Dangerous substances:
see SDS
CS2 TE