Products

KOLALEIK

Icon
KOLALEIK

KOLALEIK is a cementitious tile adhesive with high sag resistance and prolonged open time designed for interior and exterior installations of all types of ceramics and no water sensitive natural stones and agglomerates. The creamy mixture flows effortlessly under the notched trowel allowing a quick application both on walls and floors.

It is the ideal adhesive for professionals and for diy because it combines high performance and ease of installation in a single product.

KOLALEIK IS CLASSIFIED C2TE ACCORDING TO THE EUROPEAN STANDARD EN12004.

AVAILABLE FORMATS - KL1 WHITE
CODE WEIGHT PROVIDING
KL1W20 20 KG PALLET 1200 KG
KL1W5 5 KG *BOX 4 X 5 KG
AVAILABLE FORMATS - KL2 GREY
CODE WEIGHT PROVIDING
KL2G20 20 KG PALLET 1200 KG
KL2G5 5 KG *BOX 4 X 5 KG

*On request the boxes can be provided on pallets

ADVICE FOR USE

Surface preparation

All surfaces must be flat, structurally sound, clean, free of dust and loose parts. Cementitious screeds must have at least 28 days of curing and renders must cure one week per centimeter of thickness. Dry and porous surfaces should be dampened and excess water swept off. Installation may be made on a damp surface.


Mixing

Pour 28-32% of potable water (calculated on the total dry powder weight) into a clean pail. Add one bag of KOLALEIK powder. Mix with a slow speed mixer to a creamy, trowelable consistency. Allow mortar to rest for 5 minutes. Remix without adding any more water or powder. During use, stir occasionally to keep mix fluffy.


Application

Spread a thin layer of KOLALEIK using the flat side of the trowel. Comb on additional mortar with the notched side. Use a trowel suitable to ensure full bedding of the tile. Place tiles into wet, sticky adhesive and beat in using a rubber mallet to embed tile and adjust level. Check adhesive for complete coverage by periodically removing a tile and inspecting KOLALEIK transfer onto back of tile. Make sure the adhesive always remains sticky, if not remove and replace it with fresh product. For exterior installation, large format tiles and floors subject to heavy traffic, back butter the tiles to provide structural adhesion. The product is ready to light foot traffic approx. after 24 hours and to heavy traffic approx. after 14 days in standard conditions.


Consumption

2-4 kg/m2 depending on trowel notched size, type and size of the tile.


Warnings

For professional use only.
Consult technical data sheet and safety data sheet before use.
Use between +5°C and +40°C.
Protect from moisture, store in a dry place.

WARNINGS

Warnings
Danger H318
Causes serious eye damage.
H315
Causes skin irritation.
H335
May cause respiratory irritation.
H317
May cause an allergic skin reaction.
P261
Avoid breathing dust.
P280
Wear protective gloves/ protective clothing / eye protection / face protection.
P302+P352
IF ON SKIN:
wash with plenty of water.
P305+P351+P338
IF IN EYES:
rinse cautiously with water for several minutes.
remove contact lenses, if present and easy to do. Continue rinsing.
P310
Immediately call a POISON CENTER / doctor.
Contains
PORTLAND CEMENT- Cr (VI) < 2ppm, may produce an allergic reaction.

CE - 18

LEIK SPA - Via Alessandro Volta 10
46040 - Ponti sul Mincio - Mantova
KOLALEIK KL1 BIANCO CPR-0011810
KOLALEIK KL2 GRIGIO CPR-0021810


EN 12004
Improved cementitious adhesive for internal and external tiling on floors and walls

Reaction to fire:
Class F
Bond strength, as:
 
Early tensile adhesion strength:
≥ 1,0 N/mm²
Durability for:
 
Tensile adhesion strength after heat ageing:
≥ 1,0 N/mm²
Tensile adhesion strength after water immersion:
≥ 1,0 N/mm²
Tensile adhesion strength after freeze/thaw cycles:
≥ 1,0 N/mm²
Dangerous substances:
see SDS
C2 - TE