Products

IMPERLEIK

Icon
IMPERLEIK

IMPERLEIK is a special cementitious powder designed for waterproofing substrates before installing ceramic tiles or stone materials. The powder mixed with water turns into a flowing mixture that allows you to quickly cover large surfaces with minimum effort.

It can be applied by spatula, roller or flat brush. IMPERLEIK is a highly flexible product with very good adhesion to the most common substrates in the building industry and can be covered in a very short time; it also gives excellent resistance to weather aging and it is therefore suitable for the protection of concrete, cracked plasters, roofings, etc.

IMPERLEIK IS CLASSIFIED CM-O1P ACCORDING TO THE EUROPEAN STANDARD EN14891.

AVAILABLE FORMATS - IL1 WHITE
CODE WEIGHT PROVIDING
IL1W15 15 KG PALLET 900KG
AVAILABLE FORMATS - IL2 GREY
CODE WEIGHT PROVIDING
IL2G15 15 KG PALLET 900KG

ADVICE FOR USE

Surface preparation

All surfaces must be flat, structurally sound, clean, free of dust and loose parts. Cementitious screeds must have at least 28 days of curing and renders must cure one week per centimeter of thickness. Dry and porous surfaces should be dampened and excess water swept off. Installation may be made on a damp surface.


Mixing

Pour about 4.5 liters of water into a clean container. Add a 15 kg bag of IMPERLEIK under blending. Mix until a fluid consistency is obtained. Let the mixture rest for 2 minutes and mix again adding water to the desired consistency. The mixture thus obtained must be free of lumps. The mixing water dosage is purely indicative: it is possible to vary the consistency of IMPERLEIK by adding more or less water depending on the specific application.


Application

Apply IMPERLEIK first layer 1-2 mm thick, pressing down with a flat trowel to ensure maximum adhesion to the substrate. Once hardened, apply the second coat. Lay a continuous, even layer of about 2 mm thickness covering the substrate completely. When using a glass fiber mesh, submerge it into the first layer of freshly applied IMPERLEIK pressing down with a flat trowel. Wait at least 24 hours before installing tiles with KOLALEIK. Protect from early rain until fully hardened.


Consumption

1.0-1.2 kg/m2 per mm of thickness.


Warnings

For professional use only.
Consult technical data sheet and safety data sheet before use. Use between +5°C and +40°C.
Protect from moisture, store in a dry place.

WARNINGS

Warnings
Danger H318
Causes serious eye damage.
H315
Causes skin irritation.
H335
May cause respiratory irritation.
H317
May cause an allergic skin reaction.
P261
Avoid breathing dust.
P280
Wear protective gloves/ protective clothing / eye protection / face protection.
P302+P352
IF ON SKIN:
wash with plenty of water.
P305+P351+P338
IF IN EYES:
rinse cautiously with water for several minutes.
remove contact lenses, if present and easy to do. Continue rinsing.
P310
Immediately call a POISON CENTER / doctor.
Contains
PORTLAND CEMENT- Cr (VI) < 2ppm, may produce an allergic reaction.

CE - 18

LEIK SPA - Via Alessandro Volta 10
46040 - Ponti sul Mincio - Mantova
IMPERLEIK BIANCO – IL1 CPR-0091905
IMPERLEIK GRIGIO – IL2 CPR-0081905


EN 14891
Liquid applied water impermeable cementitious product (CM O1P)

Early tensile adhesion strength:
≥ 0,5 N/mm²
Waterproofing:
no penetration
Crack bridging ability:
≥ 0,75 mm to 23° C
≥ 0,75 mm to -5°C
Durability for:
 
Tensile adhesion strength after ageing:
≥ 0,5 N/mm²
Tensile adhesion strength after water immersion:
≥ 0,5 N/mm²
Tensile adhesion strength after contact with lime water:
≥ 0,5 N/mm²
Tensile adhesion strength after freeze/thaw cycles:
≥ 0,5 N/mm²
Dangerous substances:
see SDS
CM - 01P